Voltage Conversion Cable
This voltage conversion cable is a replacement product when original cable is damaged, lost, or fails to operate properly.
The cable plugs into the 2.1 amp USB port on the 28 amp-hour Power Bank supplied with the Professional Station Go Bag, and generates sufficient output power at 12 volts to operate the DMX or MMX in receive and transmit mode. Note that while you can receive when plugged into the 1 amp output USB port, your ability to transmit will be severely impacted or prevented.
The voltage conversion cable will of course work with any power bank with a 2 amp output port.
IMPORTANT: This cable provides 12V with current limit. This prevents damage to your PA (power amplifier) when under stress from high SWR. This is a very valuable safety feature.
HF, UHF/VHF 5W Dummy Load to 6GHz
You asked for it, so here it is, a 5W Dummy Load, with a male SMA connector. This is rated up to 6 GHz, so HF should be no problem for it, but you can use it on your VHF/UHF radios as well with no problem.
The radiator fins are a very nice touch in the design, and it is 100% efficient: it turns every microwatt of your RF energy into ... heat! It comes with a cap to protect the SMA plug and keep it clean of debris when not in use. This ensures a good electrical contact when you plug it in. Dirt on the contacts and cause poor conductivity and thus high resistance above the desired 50 ohms, and thus, high SWR. So keep it clean! Don't lose the cap!
Low Loss 8m (26 ¼ foot) Antenna Male to Female SMA Coax Cable
This LMR-100 low loss coaxial cable is the big brother to the 3m cable that is a part of the Professional Station GO Bag outfit for a complete radio station in a portable 8 pound bag. It connects from the DMX-40 or MMX Morse Code Transceiver output antenna connector to the 40/20M No-Tune End-Fed Antenna, also included in the GO Bag, and manufactured by PreppComm for low SWR across the entire 40/20M band.
Replacement or Extend Length
This high power coax cable can be used to replace a damaged or missing cable from a GO Bag system, or can also be used to extend the original cable length, if desired. Up to 2 cables can be daisy-chained, for a total length of over 52 feet with slightly increased loss of power to the antenna. Or, you can add this to your 3m cable and get about 36' of total length. Lengths longer than 40 feet require LMR-200 or LMR-400 to reduce power loss during transmit.
Note: These dice are made from Glass and are fragile. Roll with care and we recommend only rolling them on a soft surface. These dice can chip if rolled on a hard surface.
7 Dice Set Includes Gift Box:
1-D4 (20mm)
1-D6 (16mm)
1-D8 (16mm)
1-D10 (16mm)
1-D% (16mm)
1-D12 (18mm)
1-D20 (20mm)
Material: Glass
Purchase any 3 minis from DM Stash's Ill Omens Pt. III: Aberrant Ascension set (this one included) to digitally receive with your order the companion 106-page 5E module by DM Stash for character levels 16-20!
----
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
Purchase any 3 minis from the Darkest Depths set (this one included) to digitally receive Arisen Depths Pt. III: Beneath the Waves! It is an 89-page 5E module by DM Stash for character levels 13-15.
----
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
Note: These dice are handmade, hand-polished, and hand-painted. They are very sharp. Please handle with care. Handmade dice may not be 100% perfect, and may have tiny imperfections.
Note: The D4 has a special teardrop shape but rolls normally. The eyes are suspended in a liquid core and will move around while the dice are in motion. The liquid core is hand placed in each shape and may not be perfectly centered.
7 Dice Set Includes:
1-D4 (15mm)
1-D6 (15mm)
1-D8 (16mm)
1-D10 (16mm)
1-D% (16mm)
1-D12 (18mm)
1-D20 (22mm)
Material: Resin
The Accessories Pro Kit is a professional marker set designed to improve scan quality and tracking stability in 3D scanning workflows. It includes 6mm magnetic marker balls, adhesive markers, marker cards, fixture columns, and a 300mm turntable. With flexible and reusable magnetic components, the Accessories Pro Kit is especially effective for scanning featureless, or complex objects—ensuring accurate alignment and minimizing tracking loss.
Highest Quality Strain Relief Plus Connector Adaptor
If you are using an existing antenna system, before you do, make sure the SWR is below 2:1 before connecting it to the MMX or DMX-40.
This adaptor cable is designed to connect between the rear SMA female antenna connector on the MMX or DMX-40 and the standard antenna PL-239 plug. It also serves a second purpose, which is to reduce mechanical stress on both the PL-239 and its attachment to its likely stiff RF cable, and the very light and portable MMX with its PC-mounted SMA female connector.
These cables are extremely well built, with multiple layers of sleeving to reduce the stress on the solder joints, in order to provide long life. At the SMA connector end, note the two-lawyer cable relief design. At the SO-239 end, a 3-layer cable relief design is used to compensate for the larger connector. In addition, a clear cap is provided to protect the internal surfaces of the connector when not in use.
Keep an Extra on Hand!
We suggest, at this low price, you consider purchasing two adaptors, as all of the stress caused by the heavy duty PL-239 connector and coax will be handled by this adaptor, and thus, depending on your use case, it is the most likely to fail first. Don't be without when that happens after a few years - have a spare handy!
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
African Bloodstone Gemstone DND Dice Set
Embrace the primal power of the earth with this stunning set of African Bloodstone gemstone DND dice set! Each die is meticulously hand-carved, showcasing the unique beauty and rich history of this captivating gemstone. Channel the energy of ancient flames as you roll these exquisite dice, adding a touch of magic to your tabletop adventures.
What's in the box?
✅ 7 Hand-Carved Gemstone Dice (d4, d6, d8, d10, d%, d12, d20)✅ Free Dice Box (automatically added to cart for full sets) ✅ Felt Pouch (for single d20)
Features:
✅ Each die is meticulously carved from genuine African Bloodstone, ensuring a one-of-a-kind appearance.✅ The natural variations in Bloodstone's deep green hues and red speckles make every set truly special.✅ Perfect for Dungeons and Dragons, Pathfinder, or any tabletop RPG, this set makes a unique gift for the discerning adventurer.
Important Note: Gemstone dice are delicate and can chip if dropped on hard surfaces. Roll with care on a soft surface like a dice tray or playmat.
Purchase any 3 minis from the Darkest Depths set (this one included) to digitally receive Arisen Depths Pt. III: Beneath the Waves! It is an 89-page 5E module by DM Stash for character levels 13-15.
----
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
All our 3D printed minis come free of supports and fully cleaned and cured. They are supplied unprimed & unpainted, and they ship assembled unless the miniature has several interchangeable accessories included with it, or the customer requests it to be shipped unassembled. Stock photos are 3D renders of the models, and are not the color we typically print in (we use Navy Grey as our default). Any additional photos on a mini page are going to be actual photos of the models we print!
